Latest Articles in Auto Glass

  • 2010 Honda Fit
    Windshield and back glass removal and replacement instructions
    HondaFitthumb.jpg
    April 16, 2010
    The windshield is surprisingly large for such a small vehicle. Although it should be easy to cut out, you may need a second technician to help set the glass. The back glass will require two technicians: one to attach the defroster connectors, the other to hold the glass.

  • 2010 Honda Pilot
    Windshield and back glass removal and replacement instructions
    March 30, 2010
    Failure to use a replacement windshield with an acoustic interlayer might result in vehicle performance issues, as the interlayer might be required to allow for voice activation devices.

  • 2010 BMW X6 M
    Windshield and back glass removal and replacement instructions
    BMW X6 M_thumb.jpg
    March 15, 2010
    It has been reported that all BMW rain sensors, with the exception of those on the 3 Series, must be re-calibrated at the dealer. Research is ongoing to determine if this is the case, but be prepared to report this to the customer.

  • 2010 Buick LaCrosse
    Windshield and back glass removal and replacement instructions
    10BuickLacrosse-Thumb.png
    February 25, 2010
    The removed windshield had a decorative panel above the mirror that housed a condensation sensor and a high-powered receiver. The technician will have to remove the sensor and receiver to install the new glass.

  • 2010 Audi Q5
    Windshield, quarter glass, and back glass removal and replacement instructions
    AudiQ5thumb.jpg
    February 16, 2010
    The top edge of the windshield is exposed and extremely close to the pinchweld wall. Before cutting the glass out, tape the entire top edge of the vehicle pinchweld. Cut the sides and bottom first so you can stretch the urethane downward while cutting the top bead. This will require a second technician. Alternatively, use a length of wire to cut the top bead. Do not use an inside cutting tool as...

  • 2010 Nissan cube
    Windshield removal and replacement instructions
    January 21, 2010
    This windshield is relatively small and easy to handle but it does not have gravity stops.

  • 2010 Ford Flex
    Windshield removal and replacement instructions
    FRD_ECO_SKV9245-thumb.jpg
    January 15, 2010
    The A-pillar reveal moldings are easily damaged if not removed properly.

  • 1999 Chevrolet Silverado
    January 1, 2010
    This free, PDF download includes glass removal and replacement instructions for the 1999 Chevrolet Silverado.

  • 2009 Nissan Murano
    Windshield, quarter glass, and back glass removal and replacement instructions
    nissanmurano51thumb.jpg
    December 19, 2009
    Sponsored by Dow Automotive. The glass on this vehicle is a recommended two-person set. Also note, the A-pillar moldings have a self-adhesive-attached retainer. Carefully peel out the top portion of the molding without peeling out the retainer. If the retainer is removed, it must be replaced.

  • 2009 Infiniti G37

    Windshield, quarter glass, and back glass removal and replacement instructions
    InfinitiG37Thumb.jpg
    December 15, 2009
    Sponsored by Dow Automotive. The back glass on this vehicle is exposed on all sides and there is plenty of room between the glass and the wall of the pinchweld; however, the floor of the pinchweld is exposed also, so take care during cutout, priming, and bead placement.
Page 4 of 43
 << First | < Previous …| 2 | 3 | 4 | 5 | 6 …| Next > | Last >> 

What's Hot

  • Redefining the interior
    This commercial office space in Tulsa, Okla., features a 42-foot-long, custom, continuous art mural that spans 14 glass panels. 
    Great Glazing: Custom interior officeThis commercial office space in Tulsa, Okla., features a 42-foot-long, custom, continuous art mural that spans 14 glass panels suspended from the ceiling. Created by Tulsa artist May Yang, the mural is based on local Oklahoma themes, transitioning from rural landscape to the Tulsa skyline.   Great Glazing: Joliet Junior College Campus...
  • Top Metal Companies
    A look at the leading manufacturers and fabricators of metal products, broken down by sales volume, number of locations and product offering. 
    Building on the success of the Top Glass Fabricators rankings introduced last year, Glass Magazine is expanding its coverage to include the Top Metal Companies, featuring the leading manufacturers and fabricators of metal products in the United States and Canada. The Top Metal Companies include those that manufacture, fabricate and sell curtain wall, storefront and entrance, commercial interior...
  • 2012 Glass Magazine Award Winners: The People
    Read about the winners
    In an effort to spotlight the people who make the Glass Magazine Award-winning products and projects possible, this year’s program included people-centric categories, for which the industry submitted their picks for best installer, production supervisor, project manager and sales rep.After narrowing down the nominations to three finalists in each category, the Glass Magazine editors asked the...