Latest Articles in Auto Glass

  • Windshield and back glass removal and replacement instructions
    F150Thumb.jpg
    Sponsored by Extractor. The perimeter of the back glass provides plenty of room to cut out the part without damage. However, there is so much room that the floor of the pinchweld is visible, and care must be taken to avoid damaging the paint under the back glass.
  • Windshield removal and replacement instructions
    09A4_01_hr__mid_teaser.jpg
    Sponsored by Extractor. The top edge of the windshield is exposed and close to the wall of the pinchweld. The PAAS material might protect the wall if the cutout is done carefully. However, if salvage is the goal, it might require special cutout procedures or wire-out tools.
  • Windshield, quarter glass and back glass removal and replacement instructions
    borrego_07_Web.jpg
    Sponsored by Extractor. The A-pillar moldings on this vehicle are clipped down and might have to be replaced. The top edge of the windshield is exposed and tight to the vehicle body; cutout without damage will be difficult. This vehicle has the option of a quarter glass with a built-in antenna that will require the removal of the interior molding to connect and disconnect.
  • Windshield, front and rear door glass, quarter glass and back glass removal and replacement instructions
    09InfEX35_130.jpg
    Sponsored by Extractor. At the time these installation instructions were written, the door glasses were a dealer purchase. The dealer glass comes bonded with two tabs at the base for attaching the glass to the regulator. Also note that the front edge of the luggage rack overlaps the edge of the windshield top molding. You will be able to clear the edge of the luggage rack during cutout, but it...
  • Windshield removal and replacement instructions
    Sponsored by Extractor© 2009 National Glass Association. All rights reserved. Visit GlassMagazine.com for glass removal and replacement instructions for more than 400 vehicles. To sign up to receive the For Technicians Only e-bulletin, email FTO@glass.org. Vehicle type: Four-door sedanNAGS® numbers*: Windshield part numbers FW2560; FW2561 heated wiper park; FW2562 heated wiper park...
  • Windshield, quarter glass, and back glass removal and replacement instructions
    Sponsored by Extractor. The top corners of the top and side windshield moldings stick up, even on the OE installation. Make sure to point this out to the customer before beginning the installation. 
  • Windshield removal and replacement instructions
    Sponsored by Extractor. The top and side moldings on this windshield are underside moldings that will come with the replacement glass. If your goal is to salvage the glass, miter the aftermarket underside moldings in the two top corners.
  • Windshield and back glass removal and replacement instructions
    Sponsored by Extractor. The back glass on this vehicle fits extremely tight to the vehicle body and is exposed on all sides, making an outside cutout impossible. You may need to break the glass to remove it cleanly from the vehicle and avoid damage to the body. To salvage the glass, have the rear deck painted to correct any damage incurred during cutout.
  • Windshield, quarter glass and back glass removal and replacement instructions
    Sponsored by Extractor. The cowl panel has several underside retainers with an aggressive grip that can cause the panel to break during removal.
  • Windshield removal and replacement instructions
    Sponsored by Extractor.
Page 5 of 43
 << First | < Previous 3 | 4 | 6 | 7 Next > | Last >> 

What's Hot

  • This commercial office space in Tulsa, Okla., features a 42-foot-long, custom, continuous art mural that spans 14 glass panels. 
    Great Glazing: Custom interior officeThis commercial office space in Tulsa, Okla., features a 42-foot-long, custom, continuous art mural that spans 14 glass panels suspended from the ceiling. Created by Tulsa artist May Yang, the mural is based on local Oklahoma themes, transitioning from rural landscape to the Tulsa skyline.   Great Glazing: Joliet Junior College Campus...
  • A look at the leading manufacturers and fabricators of metal products, broken down by sales volume, number of locations and product offering. 
    Building on the success of the Top Glass Fabricators rankings introduced last year, Glass Magazine is expanding its coverage to include the Top Metal Companies, featuring the leading manufacturers and fabricators of metal products in the United States and Canada. The Top Metal Companies include those that manufacture, fabricate and sell curtain wall, storefront and entrance, commercial interior...
  • Read about the winners
    In an effort to spotlight the people who make the Glass Magazine Award-winning products and projects possible, this year’s program included people-centric categories, for which the industry submitted their picks for best installer, production supervisor, project manager and sales rep.After narrowing down the nominations to three finalists in each category, the Glass Magazine editors asked the...